To prevent scratches and dirt buildup on industrial wood floors, regular cleaning is a must. However, cleaning these floors isn’t a straightforward task. Using harsh cleaning agents can cause discoloration and deformation of the wood. Wiping with a dry cloth or warm water might not always suffice. So, what’s the solution? Below, we ‘ll guide you through five effective methods to clean wood floors.
Method 1 to Clean Wood Floors: Overall Cleaning
- Daily Sweeping: Dedicate a few moments each day to sweep away dry dust on the floor to maintain its cleanliness and prevent scratches. While high-quality industrial wood floors are resistant to scratches and dirt, small fragments can still cause damage. Regular sweeping prevents these scratches.
- Use a Soft Brush: In addition to using a broom or a vacuum cleaner, you can opt for a soft brush. Note: avoid stiff-bristle brushes as they can damage the wood. Sweep in the direction of the wood’s grain to clean debris trapped in between the floorboards.
- Immediate Spill Cleanup: When liquids spill on the floor, use a cloth or a sponge to clean it immediately. Never allow liquids to linger on the floor as they can cause staining, damage the protective layer, and lead to warping.
Method 2 to Clean Wood Floors: Warm Water
- You can use warm, not boiling, water to clean industrial wood floors. Soak a cloth in warm water, wring it out, and then use it to wipe the floor.
- If done correctly, warm water can serve as an effective cleaning agent without compromising the wood’s quality.
Method 3 to Clean Wood Floors: Vinegar
- For tough, stubborn stains that water can’t remove, create a vinegar and water solution. Combine 60 ml of white vinegar with 940-1000 ml of water in a spray bottle. Shake the mixture to dissolve the vinegar.
- Diluted vinegar is especially helpful for tackling persistent stains over time. However, as vinegar can potentially erode the wood’s surface, it should be mixed with water to form a gentle cleaning solution.
- Additionally, you can combine vinegar, dishwashing soap, and water. Mix approximately 80 ml of vinegar with a bit of dish soap and 4 liters of warm water, then spray the solution on the floor and wipe it with a cloth.
- When using vinegar to clean industrial wood floors, keep these points in mind:
- Avoid letting the vinegar sit on the floor for an extended period.
- Spray the vinegar in smaller sections (~30cm) at a time.
- After spraying, make sure to wipe it up promptly. Leaving it for too long can damage the floor’s surface.
Method 4 to Clean Wood Floors: Gentle Soap
- Pour around 4 liters of warm water into a large bucket. Add about 30 ml of mild detergent or baby shampoo. Soak a cloth or a sponge in this solution. Wring it so it’s damp, not soaking wet, and use it to clean the floor.
- If you use a minimal amount of water for cleaning, you can allow the floor to air dry. If not, use a soft, dry cloth to wipe away any excess moisture. Never let the floor stay too wet.
- Besides a cloth, you can use a mop for more efficient cleaning.
- Avoid using scented or colored detergents, as they can potentially cause color bleeding or damage the wood’s surface. Additionally, avoid using abrasive cleaning agents like bleach or strong chemicals.
Method 5 to Clean Wood Floors: Spot Stain Removal
- Blood Stains: When blood gets on the floor, clean it with window cleaner. Spray a small amount on the stain and wipe it off immediately with a slightly damp cloth.
- Chewing Gum: For gum stuck to the floor, you can gently scrape it off with a plastic knife. Then wipe away any remaining residue with a soft, damp cloth.
- Nail Polish: Use nail polish remover with a small amount of water on a cloth to eliminate nail polish stains. Afterward, wipe the area with a clean, damp cloth.
- Scuff Marks: You can remove scuff marks by gently rubbing a pencil eraser.
By following these 5 simple and effective methods to clean wood floors, you can maintain your wood floors’ cleanliness and beauty effectively.